Report item
Item specifics
  • Products Status: Stock
  • Package: No
  • Model Number: DCS810
  • Type: DRIVER
Product Description

Wholesale, Free shipping Leadshine Digital DC servo Drive DCS810 up to 80 VDC/20A, Power Up to 400W servo motor Drivers

Feature :

  • 18-80VDC, 0-20A, 20-400W.  
  • Based on DSP control technology and high smooth servo control algorithm.  
  • Parameter visible tuning tools, including Pro Tuner and STU.  
  • Feedback resolution X4 encoder line count.  
  • Position Following error lock range adjustable  
  • Position error can be eliminated to 1 count, and Velocity error can be eliminated to the Desired Velocity* 0.3%  
  • Electronic gear ratio from 1/255 to 255  
  • Built-in motion controller for self-test with trapezoidal velocity profile  
  • Support PUL/DIR and CW/CCW control signals  
  • Opto-isolated inputs, support single-ended and differential signals  
  • 10 latest errors self-record function  
  • Over-current, over-voltage, under-voltage, phase error, encoder error, position following error protections  
  • Small size, surface-mount technology  

Introduction :

 

The DCS810 is a digital DC servo driver developed with DSP and high efficient MOSFET technologies. In position control, it\'s easy for the end users to change stepping drivers to the DCS810 without changing control systems, because its input command is PUL/DIR signal, which is compatible with that of stepping drivers. In low power motion control applications, performances of DC servo systems using the DCS810 are better than those of digital AC servo systems in velocity, precision, noise, stability, or at least as good as those of digital AC servo systems. However, the cost of the DCS810 stays at the price line of stepping driver, namely far lower than those of AC servo drivers.

Compared to the DCS810S, the DCS810 can accept differential control signals and differential encoder feedback signals, offering better anti-interference performances. Compared to the DB810A, parameter visible tuning tools make the DCS810 much easier to tune.

The DCS810 is very easy to tune and all parameters are visible. Parameter visible tuning tools, including Pro Tuner (Windows based setup software) and STU (Small servo tuning unit) can meet different tuning environments or requirements.

Specifications :

 General

   Parameters

DCS303

Min.

Typical

Max.

Unit

   Peak output current

0

-

20

A

   Supply voltage

+18

+24

+80

VDC

   Logic signal current

7

10

15

mA

   Pulse input frequency

0

-

500

kHz

   Isolation resistance

500

 

 

Mohm

   Current provided to encoder

 

 

50

mA

 

General information :

 

Control Signal Connector

Pin

Signal

Description

I/O

1

PUL

Pulse control signal

I

2

DIR

Direction control signal

I

3

OPTO

+5V Opto-isolated power input

I

4

ENA

Enable control signal, can be used to clear position following error

I

5

ERR

Error output signal, HIGH indicates normal, LOW indicates fault.

O

6

EGD

Opto-isolated GND, use for reference when using ERR

GND

Encoder Signal Connector

Pin

Signal

Description

I/O

1

EB

Encoder channel B input.

I

2

EA

Encoder channel A input.

I

3

E +5V

Positive pole of the auxiliary power supply (50 mA (Max)).

O

4

EGND

Ground of the auxiliary power supply.

GND

Power Connector

Pin

Signal

Description

I/O

1

Motor+

Motor positive connection.

O

2

Motor-

Motor negative connection.

O

3

+Vdc

+18 TO 30 VDC power input.

I

4

GND

Power Ground.

GND

RS232 Communication Connector

Pin

Signal

Description

I/O

1

+5V

+5V power only for STU.

O

2

TxD

RS232 transmit.

O

3

GND

Ground.

GND

4

RxD

RS232 receive.

I

 

More about PUL/DIR/ENA Signals

Pin Function

Details

PUL

Pulse signal: This input represents pulse signal; 4-5V when PUL-HIGH, 0-0.5V when PUL-LOW. For reliable response, pulse width should be longer than 2.5µs. Series connect resistors for current-limiting when using +12V or +24V control signals (OPTO). The same as DIR and ENA signals.

DIR

DIR signal: This signal has low/high voltage levels, 4-5V when DIR-HIGH, 0-0.5V when DIR-LOW. For reliable motion response, DIR signal should be ahead of PUL signal by 5µs at least. Please note that motion direction is also related to motor-driver wirings and encoder feedback A/B phase signals. Exchanging the connections of two wires of the motor to the driver and A/B phase signals of encoder will reverse motion direction.

ENA

Enable signal: This signal is used for enabling/disabling the driver. High level (NPN control signal, PNP and Differential control signals are on the contrary, namely Low level for enabling.) for enabling the driver and low level for disabling the driver. Usually left UNCONNECTED (ENABLED).

ERR

Error signal: This pin will be pulled to LOW level (reference to EGD) when driver goes into faulty status. There is a 10K resistor connected between ERR and OPTO. Please refer to figure 2 in Control Signal Connections for more details.

 

Typical Connections :

D9-2

 

Mechanical Specifications

D9-3

 

Payment

> We accept Aliexpress Escrow as our payment method, others way please contact us.

Shipping

>Our delivery day for normal items will be about 5 days to 15 days to the following countries: USA, The United Kingdom, France, 
Canada, Australia, Russia.

 >We shall ship you items within 3 business days after your payment is cleared.

>Please make sure your address is accurate, so we only ship the items to your Aliexpress address.

>Once shipping, we will send tracking number to your, it usually takes 3 -8 business days to make the tracking informations online, if you do not receive item within 30 business days please contact us.

Returns

> If you are not satisfied with your purchasing for any reason, you can return the item to us, please send the email to us before returning.

> It must be returned within 14 days, return shipping fee will be paid by buyer.

>Once we get the item we will exchange or refund your money, but not including shipping &handling and insurance fee.

>If you return the part been used, we can not accept it and refund you 

 

 

Packaging Details
  • Unit Type: piece
  • Package Weight: 0.35kg (0.77lb.)
  • Package Size: 20cm x 15cm x 10cm (7.87in x 5.91in x 3.94in)
Shipping
Calculate your shipping cost by country/region and quantity.
Quantity: Ship to:
Packaging Details
  • Unit Type: piece
  • Package Weight: 0.35kg (0.77lb.)
  • Package Size: 20cm x 15cm x 10cm (7.87in x 5.91in x 3.94in)
Payment
We support the following payment methods. All payments made on AliExpress are processed by Alipay.