Report item
Item specifics
Product Description



The 24 port Gigabit Ethernet switch

  • 24 adaptive 10/100/1000M RJ45 port
  • All ports have the line speed forwarding capability
  • Support auto flip port (Auto MDI/MDIX) function
  • Provide convergence alliance, network clone and share three kinds of working mode, to adapt to different network environment
  • Supported by a toggle switch switch switch mode
  • Plug and play, can be on the rack



    TL-SG1024T is TP-LINK designed to meet non system disk, network clone, the application and development of the second layer Gigabit non network Ethernet switch products, provide 24 10/100/1000M RJ45 port, support all port line speed forwarding. This series of switches provide different working modes for the application of diskless network, g good network adaptability.

    Port performance

    Provides 24 10/100/1000M adaptive RJ45 port, all ports can achieve line speed forwarding;

    Each port supports MDI/MDIX automatic turning and duplex auto negotiation / rate;

    Support IEEE 802.3x full duplex flow control and Backpressure half duplex flow control.

    Three working modes

    Provide mode switch to support three operating modes of the gathering "couplet" and "shared" and "network clone", and can be optimized to support a non system disk, network clone other network applications.

    Simple to use

    Standard 19 inch rack installation, plug and play, without management; dynamic LED indicator, provide working state and fault prompt simple exclusion.

    Hardware Specifications

    Supported Standards

    • IEEE 802.3, IEEE 802.3u
    • IEEE 802.3ab, IEEE 802.3x


    10/100M RJ45


    10/100/1000 RJ45

    • Twenty-four

    Gigabit SFP optical port



    Each port

    • Link/Act
    • Speed

    Per device

    • Power
    • System


    Store and forward

    • support

    backplane bandwidth

    • 48Gbps

    address table

    • 8K


    • Working temperature: 0 to 40 DEG C
    • Storage temperature: -40 to 70 DEG C
    • Working humidity: 10% ~ 90%RH, no condensation
    • Storage humidity: 5% ~ 90%RH, no condensation

    Power Supply

    • Input: 100-240V ~ 50/60Hz

    Size (L * W * H)

    • 440mm x 180mm x 44mm

    Functional specifications


    Three mode switch

    • M1: Network Clone
    • M2: Sharing Standard
    • On the convergence of M3:



Functional specifications


Three mode switch

  • M1: Network Clone
  • M2: Sharing Standard
  • On the convergence of M3:

    The typical application of Internet Network


    TL-SG1024T provide 24 10/100/1000M adaptive RJ45 port and supports wire speed switching, the innovation of mode switching function makes the series switches which are well adapted to the startup disk and network clone network environment, as a central switching equipment with complex TP-LINK all Gigabit intelligent network switches, especially suitable for Internet cafes, all gigabit network set up economic and efficient.

    The application of topology


    List of equipment








    Multi WAN port internet router

    Single port WAN internet router

    central exchange



    Full Gigabit Web management switch

    access switch


    The 24 port Gigabit Ethernet switch

TL-SG1024T ( Series) three kinds of mode selection

TL-SG1024TMainly to solve the network without disk cloning, slow start problem and design, compared with the ordinary switch,TL-SG1024TA three level sliding switch hardware, three optional modes: (network clone) M1, M2 (shared), m3 (aggregation uplink).

The following two kinds of common network topology as an example, introduces three modes in different network application environment selection.
1, large and medium-sized network environment: the center switch adopts three layer switch or managed switches, access layerTL-SG1024TThe following figure:


2, small network environment: the whole network useTL-SG1024TThe switch, as shown below:



In view of the above two kinds of network environment, how to adjustTL-SG1024TPlease refer to the table of the work mode:




1,TL-SG1024TAs the central switch, because of the limited amount of belt machine, the switch to less than 3.

2 time, M1, M2, M3 mode switch to restart switch effect.

Why do some computer can not access connected to the switch?
The cause of this situation may have: the physical connection is not stable, computer is set properly, please click the following steps out:

1, the replacement between the computer and the switch cable, to ensure that the switch corresponding to the indicating lamp is bright, the local stable connection. Inspection method: switch connected two computers, set in the same segment, between if pass, between the computer and the exchange connection is stable.

2, the local computer connection is set to automatically obtain IP (premise front-end router DHCP server), right click the local connection properties, select the Internet protocol (TCP/IP), click the properties button.



3, select "obtain an IP address automatically, and then determine the.


4, when the computer gets normal after IP can be normal internet.



5, if the normal access is still not online, please check the front-end router settings, whether to prevent the computer on the internet.

6, if not normal access to the IP address, the replacement between the switch and the router network.

Packaging Details
  • Unit Type: piece
  • Package Weight: 1.0kg (2.20lb.)
  • Package Size: 1cm x 1cm x 1cm (0.39in x 0.39in x 0.39in)
Calculate your shipping cost by country/region and quantity.
Quantity: Ship to:
Packaging Details
  • Unit Type: piece
  • Package Weight: 1.0kg (2.20lb.)
  • Package Size: 1cm x 1cm x 1cm (0.39in x 0.39in x 0.39in)
We support the following payment methods. All payments made on AliExpress are processed by Alipay.